RGB Gesture Recognition Sensor Module IIC I2C Optical Ranging for Arduino

Description: GY-PAJ7620U2 Description: PAJ7620U2 integrates gesture recognition function with general I2C interface into a single chip. It can recognize 9 gestures including move up, move down, move left, move right, move forward, move backward, circle-clockwise, circle-counter clockwise, and wave. These gestures information can be simply accessed viathe I2C bus. The PAJ7620U2 also offers built-in proximity detection for the purpose of sensing object approaching or departing. The PAJ7620U2 is designed with great flexibility in power-saving mechanism. The PAJ7620U2 is designed to operate from 2.8V to 3.3V over -40°C to +85°C and the pull-up voltage for the I2C bus and interrupt line is from 1.8V to 3.3V. Feature: • Typical supply voltage is 2.8V to 3.3V and I/O voltage is 1.8V~3.3V • Nine gesture recognition (Up / Down / Left / Right / Push / Pull / CW / CCW / Wave) • Gesture speed is 60°/s to 600°/s in Normal Mode and 60°/s to 1200°/s in Gaming Mode • Ambient light immunity: < 100k Lux • Built-in proximity detection • Flexible power saving scheme • I2C interface up to 400 kbit/s, Pull-up voltage from 1.8V to 3.3V • Ambient light noise cancellation Application: •PAD Phone •Tablet Personal Computer •Automobile Application PAJ7620U2 Introduction: This is a gesture recognition sensor based on PAJ7620U2. It can recognize 9 different gestures including up, down, left, right, front, back, clockwise, counterclockwise, and swing. The gesture recognition module uses the I2C interface and it use the corresponding Arduino library function to program and control. The signal returned by the gesture recognition module can be used as a control signal received by the robot to implement the control of the robot. The built-in recognition algorithm is smart enough to free your hands from the hard keys. Gesture recognition sensors can be used for non-contact control scenarios such as non-contact mice, smart homes, automotive electrical equipment controls, robot interactions, and more. Product parameters: Detection chip: PAJ7620U2 Operating voltage: 3.3~5V Communication Protocol: I2C Interface Communication Protocol Detection distance: 50mm~100mm Module size: 19.7mm*15mm Induction action: up, down, left, right, front, back, clockwise, counterclockwise Pin description: GND: negative input of power VCC: positive power input port, can access 3.3 ~ 5V voltage SCL: I2C clock port SDA: I2C data port INT: Interrupt output APDS-9960 Built-in APDS-9960 sensor, providing ambient light and color measurement, proximity detection and non-contact gesture detection. With this RGB and gesture sensor, you can control a computer, a microcontroller, a robot, and it's much more powerful than a simple credit card with your hand! In fact, the gesture sensor APDS-9960 was used in the Samsung GalaxyS5. The APDS-9960 is a serious little piece of hardware with built in UV and IR blocking filters, four separate diodes sensitive to different directions, and an I2C compatible interface. For your convenience we have broken out the following pins: VL (optional power to IR LED), GND (Ground), VCC (power to APDS-9960 sensor), SDA (I2C data), SCL (I2C clock), and INT (interrupt). Each APDS-9960 also has a detection range of 4 to 8 inches (10 to 20 cm). Can be applied to ambient light and RGB color sensor, close to detection, gesture detection. Product Parameters: Operating voltage: 3.3V Measuring range: 4-8 in (10-20CM) I2C Interface Product Schematic: APDS-9960 GY-9960-LLC APDS-9960 is an integrated ALS, infrared LED and proximity detector optical module and ambient brightness sensing (ALS, Ambient Light Sensing) of the ambient brightness sensor, the use of dual-light diode to approximate 0.01 lux illumination similar to the human eye visual response Programmable interrupt function with upper and lower thresholds up to 16-bit resolution for high flexibility even after dark glass, 100mm object detection for close proximity sensors, free of end devices and subassemblies Of the factory calibration requirements. Ambient light dynamic range from the previous 10K lux increased to 30K lux, the sun calibration greatly increased to 50K lux, greatly enhance the sensitivity and avoid the strong light interference. You can work in a large 1.0mm Air Gap precision work, do not do external isolation processing, greatly facilitate the customer's structural design. Its state of standby power consumption - 90μA typical, sleep mode power - 2.2μA typical, more energy saving; up to 400kHz (I2C fast mode) dedicated interrupt pin, providing I2C interface compatible, fully integrated solution for easy structure and circuit design , I believe to give users a better design experience and product value! It includes APDS-9960 sensor, providing ambient light and color measurement, proximity detection and contactless gesture detection. With this RGB and gesture sensor, you can control a computer, microcontroller, robot, it's more powerful than your hand a simple swipe function! In fact, the gesture sensor APDS-9960 was used in Samsung GalaxyS5. It could be applied to ambient light and RGB color sensor, proximity detection, gesture detection. Product Parameters Operating voltage: 3.3V Measuring range: 4-8in (10-20CM) I2C interface APDS-9960 Built-in APDS-9960 sensor, providing ambient light and color measurement, proximity detection and non-contact gesture detection. With this RGB and gesture sensor, you can control a computer, a microcontroller, a robot, and it's much more powerful than a simple credit card with your hand! In fact, the gesture sensor APDS-9960 was used in the Samsung GalaxyS5. The APDS-9960 is a serious little piece of hardware with built in UV and IR blocking filters, four separate diodes sensitive to different directions, and an I2C compatible interface. For your convenience we have broken out the following pins: VL (optional power to IR LED), GND (Ground), VCC (power to APDS-9960 sensor), SDA (I2C data), SCL (I2C clock), and INT (interrupt). Each APDS-9960 also has a detection range of 4 to 8 inches (10 to 20 cm). Can be applied to ambient light and RGB color sensor, close to detection, gesture detection. Operating voltage: 3.3V Measuring range: 4-8 in (10-20CM) I2C Interface VL6180X The VL6180x three-in-one optoelectronic module integrates an IR VSEL (vertical-cavity surface-emitting laser) infrared vertical cavity surface emitting laser source, proximity sensor, and ambient light sensor (ALS). The VL6180X module implements a proximity sensor using the time-of-flight (ToF) measurement principle; the VL6180X includes a SPAD (Single Photon Avalanche Diode) detector array that detects the time at which a single photon is transmitted from the target to the target and back to the module, calculated in conjunction with the signal amplitude. The actual distance, independent of the reflectivity of the object, this actual distance measurement capability can also produce simple but reliable one-dimensional gesture control. The ambient light sensor also has high sensitivity and precision under ultra-low light, wide sensing dynamic range, and ambient light (Lux) corrected output. All components used to support proximity sensors and ambient light sensors are integrated into one packaged optical module. The embedded design can be completed without the need for a mechanical spacer or an additional lens system. Parameter: Infrared laser wavelength: 850nm Communication interface: IIC (400kHz), address 0x29 (7-bit), two programmable GPIO Optimal working temperature: -10 ~ 60 ° C Ranging performance parameters: Range (near) range: 0 to 100mm Error 13mm Under certain external environmental conditions, such as 100mm in dark environments Temperature drift: 9 ~ 15mm Voltage drift: 3 ~ 5mm Conversion time: 15ms Ambient light range: 1~100kLux 16-bit output Ambient light gain range: 1 to 40 (eight) Ambient light sensitivity: 0.36 Lux/count (535 nm LED @ 1 kLux. Measured @ gain 20) Angle response: 42 degrees Linearity error: 5% (1 to 300 Lux), 10% (300 to 7500 Lux) Gain error: 1% (gain 20), 7% (gain 1 to 10) Instructions: Vin: Power input pin. Voltage input range 3-5V; 2v8: Output port, output 2.8V voltage, the 2.8V output voltage generated by the on-board voltage regulator processing VIN input voltage, convenient to expand and use; GND: power ground; SCL: I2C clock pin, connected to the master SCL; SDA: I2C data pin, connected to the master SDA; GPIO: The pin used by the sensor to indicate that the data is ready. Note that the output of this pin is 0-2.8V high and low. This pin may not be applied to boards such as Arduino (these boards are 3.3 or 5V high). ), generally not used, to apply level conversion; SHDN: sensor off pin. By default it is pulled high. There is a level shifting diode so you can use 3-5V logic on this pin. When the pin is pulled low, the sensor enters the shutdown mode; Product testing (based on for Arduino): 1.Serial print test distance value: Wiring: 2, DIY ranging instrument demonstration Wiring: VL6180 Product Parameter: Infrared laser wavelength: 850nm Communication interface: IIC (400kHz), address 0x29 (7-bit), two programmable GPIO Optimal working temperature: -10 ~ 60 ° C Range (close) range: 0 ~ 100mm error 13mm Under certain external environmental conditions, such as in dark environments, it can exceed 100mm Temperature drift: 9 ~ 15mm Voltage drift: 3 ~ 5mm Conversion time: 15ms Ambient light range: 1~100kLux 16-bit output Ambient light gain range: 1 to 40 (eight) Ambient light sensitivity: 0.36Lux/count (535nm LED @ 1 kLux. Measured @ gain 20) Angle response: 42 degrees Linearity error: 5% (1 to 300 Lux), 10% (300 to 7500 Lux) Gain error: 1% (gain 20), 7% (gain 1 to 10) 2.8V: 2.8V voltage on the power input pin; GND: power ground; SCL: I2C clock pin, connected to the master SCL; SDA: I2C data pin, connected to the master SDA; GPIO1: A pin used by the sensor to indicate that the data is ready. APDS-9930 The APDS-9930 light environment and proximity detection module provides an I2C interface compatible ambient brightness sensor (ALS) and a proximity sensor with infrared LEDs. Among them, the high sensitivity provided by the ambient brightness sensor allows the device to operate behind dark glass, and the proximity sensor can work well under different lighting conditions. The addition of micro-optical lenses to the horizontal block provides high-efficiency transmission and reception of infrared energy, enabling the device to have a very low average power consumption. Parameter: Integrated module: integrated ALS, infrared LED and proximity detection optical module High resolution: up to 16Bit resolution makes the ambient brightness sensing similar to the human eye Visual response Effective distance: The effective distance of proximity detection is 100mm Working voltage: module working voltage 3.3V Communication protocol: I2C interface communication protocol On Dec 6, 2023 at 01:11:50 PST, seller added the following information:

Price: 4.83 USD

Location: shenzhen

End Time: 2025-02-06T08:26:43.000Z

Shipping Cost: 2.99 USD