8PCS Air Suspension Kit Front Rear Air Strut Valve Block Compressor For Mercedes

Description: *Compatibility Chart 1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number). 2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits. 3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0). Mercedes-Benz GL-ClassGL320 Bluetec 4Matic Sport Utility 4-Door 3.0L 2009GL320 CDI Sport Utility 4-Door 3.0L 2007-2008GL350 Bluetec 4Matic Sport Utility 4-Door 3.0L 2010-2012GL450 Base Sport Utility 4-Door 4.6L 2007-2012GL450 Base Sport Utility 4-Door 4.7L 2007-2009GL550 Base Sport Utility 4-Door 5.5L 2008-2011 Mercedes-Benz M-ClassML320 CDI Sport Utility 4-Door 3.0L 2007-2008ML350 4Matic Sport Utility 4-Door 3.5L 2006-2011ML350 Base Sport Utility 4-Door 3.5L 2006-2007 2009-2011ML350 Bluetec 4Matic Sport Utility 4-Door 3.0L 2010-2011ML350 Introduction Sport Utility 4-Door 3.5L 2006ML350 Lujo Sport Utility 4-Door 3.5L 2008-2009ML350 Premium Sport Utility 4-Door 3.5L 2006ML350 Sport AMG Sport Utility 4-Door 3.5L 2010-2011ML350 Sport AMG Sport Utility 4-Door 5.5L 2010-2011ML450 Hybrid 4Matic Sport Utility 4-Door 3.5L 2010-2011ML500 Base Sport Utility 4-Door 5.0L 2005-2007ML500 Introduction Sport Utility 4-Door 5.0L 2006ML500 Premium Sport Utility 4-Door 5.0L 2006ML500 Special Edition Sport Utility 4-Door 5.0L 2005ML550 Base Sport Utility 4-Door 2008-2011 *Air Suspension Structure: 10 164 320 07 31 Shock Absorber 10 164 320 20 31 Shock Absorber 10 164 320 27 31 Shock Absorber 10 164 320 30 31 Shock Absorber 20 164 540 67 10 Wiring Harness 30 164 320 02 25 Pneumatic Spring 30 164 320 06 25 Pneumatic Spring 30 164 320 09 25 Air Spring 30 164 320 10 25 Air Spring 30 166 320 03 25 Pneumatic Spring 35 000 327 00 69 Connector 70 003 997 56 90 Clamp 100 164 320 09 31 Shock Absorber 100 164 320 15 31 Shock Absorber 100 164 320 16 31 Shock Absorber 100 164 320 24 31 Shock Absorber 110 164 324 02 04 Rear Spring 110 164 324 04 04 Helical Spring 120 164 325 02 15 Spring Case 125 164 324 00 84 Shim 130 211 328 00 58 Seal Holder 140 164 320 00 56 Shim 145 166 326 04 67 Spring Plate 150 N000000003905 Nut 155 N913023010004 Nut 160 202 326 00 76 Washer 170 164 328 01 04 Cover Plate 170 164 328 02 04 Cover Plate 170 164 328 05 04 Cover Plate 170 164 328 06 04 Cover Plate 200 N000000003343 Nut 200 N000000005275 Nut 210 N910105016009 Hexagon Head Bolt 700 210 540 21 81 Clutch 710 000 545 69 80 Gasket 710 008 545 63 26 Female Contact *Generation & Evolution: Mercedes-Benz GL-ClassX164 First generation (2007-2012)X166 Second generation (2013-present) Mercedes-Benz M-ClassW163 First generation (1997-2005)W164 Second generation (2005-2011)W166 Third generation (2011-2019)W166 Sport UtilityC292 Coupé VersionW167 Fourth generation (2019-present) *Platform Drive Layout: Base Model-Rear Wheel Drive Layout 4Matic Model-Four Wheel Drive Layout *Removal Guideline: 1.Raise vehicle with lifting platform. -Raise vehicle far enough until the wheels are clear of the ground.2.Empty air spring use STAR DIAGNOSIS system. Connect STAR DIAGNOSIS and read out fault memory.3.Switch off ignition and remove the transmitter key from the EIS control unit. -On vehicles w/Keyless Go, (889), Press Keyless Go button repeatedly until ignition is switched off. Remove transmitter key from vehicle and storeit in a location beyond its transmission range (at least 2 m).4.Raise vehicle with lifting platform.5.Unscrew threaded connection for compressed air line of air suspension from the air spring. -Detach threaded air line connector from airline, make sure a clean straight cut on line.6.Carefully pull air spring downwards at its upper plastic frame until the air spring detaches from the retaining clip. -The retaining clip must be replaced during installation as it is destroyed during removal.7.Carefully push the air spring together upwards, in the process press the air spring centering from below out of the lower transverse control arm.8.Remove air spring downwards at an angle. *Installation Guideline:Caution: If the air spring is not installed and filled in accordance with the regulations, it can be pre-damaged and fail later on.1.Install the new retaining clip onto body of the vehicle. -Remove the remains of the old retianing clip from the body of the vehicle.2.Mount cover on the air spring. -The fixing journals must engage in the holes of the air spring. The curved surface of the cover must be positioned above the compressed air line connection of the air spring.3.Insert air spring. -Do not twist air spring, otherwise it will be damaged. The airspring must latch in the retaining clip and be positioned with the lug of the air spring centering correctly in the lower transverse control arm.4.Pull plastic airline fitting insert straight out and insert air line directly into airline fitting.5.Lower vehicle with lifting platform. -Only lower vehicle far enough that the wheels are still easily accessible.6.Start engine and run. -Before starting, ensure that the transmission is in the park position. -Use exhaust extraction!7.Inflate air spring using the STAR DIAGNOSIS system. Connect and read out fault memory. -Ensure that there are no leaks from the air suspension system.8.Switch off engine and lower the vehicle using the lifting platform. *Warning & Notice: Vent all air pressure from the air suspension system prior to disconnecting or removing any air suspension components. It is dangerous to remove air suspension components while under pressure. Failure to follow this instruction may result in serious personal injury. Any air spring which is unfolded must be refolded prior to being installed in a vehicle. Refer to the procedure. An incorrectly folded air spring could rupture, altering the handling characteristics of the vehicle. If a vehicle has been driven with an incorrectly folded air spring, a new air spring must be installed. Failure to follow these instructions may result in serious injury to vehicle occupant(s). Failure to observe the following instructions may result in a sudden failure of the air spring or suspension system. Any rear spring which is unfolded must be refolded prior to being installed in a vehicle. The air spring refolding procedure should only be used for an air spring which has never supported the vehicles weight while in the incorrectly folded position. Incorrectly folded air springs found on vehicles during pre-delivery inspection or after use must be installed new. Do not attempt to inflate any air spring which has been collapsed while uninflated from the rebound hanging position to the jounce stop. When installing a new air spring, care must be taken not to apply a load to the suspension until springs have been inflated using the air spring fill procedure. After inflating an air spring in the hanging position, it must be inspected for correct shape.1.NOTE: The vehicle must be positioned on a suitable lifting device prior to deflating the air suspension system.With the vehicle in NEUTRAL, position on a hoist until the wheel and tire assemblies are slightly above the ground. 2.Using the scan tool, vent the air springs.3.Remove the air spring retainer.4.Detach the air spring from the rear axle.5.Remove the air spring in the following sequence.1.Disconnect the air spring solenoid electrical connector.2.Compress the quick connect locking ring and pull out the air tube.3.Remove the air spring. *Frequently Asked Questions:How to prevent the damage of air springs/How to extend the service life of air springs/struts etc.?An air strut with separable air springsIf your vehicle offers a separable air suspension (Audi Allroad A6 C5, Mercedes-Benz W164, BMW X5, etc.), you should regularly (about once a week) lift the car to the maximum position, and remove dirt with a high-pressure cleaner (keep the cleaner at a distance to the air spring about 30 cm/12 inches, otherwise water pressure can damage the air spring). The highest position may vary depending on your model and regulation options. Therefore, please test this by trying the different modes available to you (Sport, comfort, dynamic, off-road) and choose the one that sets your vehicle to the highest position. The dirt will most likely be found under the fold of the pneumatic chambers. If you find a frozen layer of bitumen on the piston guide (the part of a strut on which the air spring is installed), it is recommended to clean it as well. Whenever possible, avoid riding on fresh asphalt, as fresh bitumen mixed with sand immediately results in a build-up of abrasives on the piston and in turn contributes to accelerated wear and tear of the air spring. A complete air suspension shockMany cars such as Mercedes W220 or W211 are set up with a complete air strut - shock absorber and air spring visually form a complete spare part. In many cases, you can easily recognize these by the metal cups with which the air spring is tightly mounted. To best avoid any damage, we highly recommend to regularly check the condition of the dust protection seals of the air strut. What is the difference between an air spring and an air strut? The air spring is a part of the air strut. Some vehicles (e.g. Mercedes ML) allow you to change the air spring separately. At our online shop you have the opportunity to buy either the whole air strut or only the air spring. For some type of vehicles it is not possible to change the air spring separately. In this case the whole air strut should be replaced. Which side of my car is the Right and Left? The right and left sides of an automobile are determined as if sitting in the car facing forward. Thus, the left side is on the left when sitting in the car facing forward, and the right side is on the right. For American cars, the driver’s side is on the left, and the passenger sits to the right of the driver. For cars in Japan, Britain, Ireland, the Bahamas and some other former British colonies -- where they drive on the left side of the road -- the passenger sits on the left side, and the driver (along with all the driving controls) is on the right. *OEM Part Number: Front Air Suspension Struts: 16432045131643206113 Rear Air Suspension Struts: 16432026311643200631 164320123116432013311643202231 1643202431 Air Suspension Compressor: 164320000416432002041643200304164320050416432009041643201204 Air Suspension Valve Block: 2123200358 1643201204 A 164 320 12 04,A 212 320 03 58 A1643201204,A2123200358 Rear Air Springs: 164320022516432004251643200625164320072516432008251643200925164320102516632003251663200625 *Item Specifications:Key Words: 8 Piece Air Suspension Kit Front Rear Air Strut Valve Block Compressor For Mercedes M-Class W164 ML320 ML350 ML450 ML500 ML550 2005-2011 GL-Class X164 GL320 GL350 GL450 GL550 2007-2012 Without Adaptive DampingPackage Includes:8 Piece Air Suspension Kit Front Rear Air Strut Valve Block Compressor Notes: Please double confirm the compatibility as well as the OEM number before purchasing.Instruction is not included. Professional installation is recommended. Shipping WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov. 1. Package handling takes about 2 business days at our warehouse, so please make sure entering correct payment and shipping information before checking out. Once your payment is completed, we are not going to accept any more changes to your order. 2.All domestic orders will be shipped via USPS, UPS or Fedex from our US warehouse and usually arrives to your door in about 2-7 business days. 3.Local pick up is not available. 4.International Buyers C Please Note: a. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyers responsibility. b. Please check with your country customs office to determine what these additional costs will be prior to bidding/buying. ] Payment 1.We accept multiple payment methods, such as PayPal, VISA, Master Card, etc.. 2.Please do not use the PayPal note field to indicate us to ship to other address. The note there will NOT be read. If you want to change the shipping address, please contact us by eBay messages. 3.(if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 4.Payment must be received within 7 days as auction ended or order might be delayed. Returns 1.All of our brand new items come with a 60-Days money-back guarantee. 2.We define the item as defective only if it doesnt function as described, It is the buyers responsibility to understand the item description before bidding. 3.We will replace the defective items, provided that they are in stock within the warranty period posted with the listing and the buyer return the original item and pay for the S&H cost for the replacement. 4.We will refund the purchase price if the replacement is not available or buyer prefers a refund and send the original item back at his/her own cost. 5.Shipping& handling cost are not refundable. 6.Man-made damage by abuse or wrong operation is not covered by this warranty. 7.No product liability insurance is assumed. 8.Refunds will be credited within 5 to 7 business days of receiving the return. When weve received and processed the return, we will refund the applicable amount minus any Recovery Fees (See Details Below) for the amount you paid for the item(s), plus any applicable sales tax. ] Customer Services Q: How do I pay for my purchase? A: MY store accepts PayPal, VISA, Master Card, etc.. Q: When will the item be shipped out? A: This item will be shipped with 2 business day once payment completed. Q: Where is my tracking number? A: Please log on your account, click "my eBay"-->"my summary", or open your email box and find the shipping notification email. Q: How do I return an item? A: My tore accepts returns. Items must be returned within 60 days. Refunds will be given as money back. Please contact our customer service before you return an item. ] Feedback 1. We will leave a feedback once we get your payment. 2. If you are dissatisfied for any reason, please do contact us a feedback. We will work hard to make sure EVERY CUSTOMER 100% SATISFIED and resolve any problem for you and always leave a feedback to all our customers. 3. If you are satisfied with the product you received, wish you can leave us a feedback. Copyright of SCITOO-AutoParts . All rights reserved.

Price: 605.4 USD

Location: Ontario, California

End Time: 2024-11-20T06:23:53.000Z

Shipping Cost: 0 USD